UDP Module Manufacturer in China — Embedded Flash Modules

In short

WINTEL is a UDP (USB Disk in Package) module manufacturer, not a trading company. A UDP module is the electronic core of a USB flash device — NAND, controller and passives moulded into a single package that is soldered directly onto your PCB as fixed internal storage. We produce them on our own floor in Shenzhen, China: 25 × 11.3 × 1.4 mm and 0.819 g on the moulded module, or a 12 × 48 × 4.5 mm semi-finished board when your own housing needs a full PCBA. Capacity runs 4GB to 32GB on the module and up to 128GB on the board, USB 2.0 or 3.0 by format. Buyers are embedded and industrial device makers who need storage that enumerates reliably and survives without a separate connector. Capacity, silicon grade, controller solution and testing are set to your specification. The legal entity is Shenzhen Wintel Digital Technology Limited, registered in China since 2015.

What we manufacture

UDP modules (USB Disk in Package)

25 × 11.3 × 1.4 mm · 0.819 g · 4GB–32GB · USB 2.0

Soldered onto your own PCB as fixed internal storage — no connector, no loose drive.

Semi-finished USB boards

12 × 48 × 4.5 mm · 3.2 g · 128MB–128GB

The bare PCBA when you run your own housing or final assembly.

Finished USB flash drives

Metal, PVC or wood body · 128MB–128GB · USB 2.0 / 3.0

When you need the complete drive rather than the embedded core.

Who we supply

Embedded device manufacturers

You design the board and need a storage core that solders in place and enumerates the same way on every unit — dashcams, IP cameras, POS terminals, kiosks, medical and industrial controllers.

Industrial equipment manufacturers

You need fixed storage that is not a removable consumer drive — no card slot to loosen, no connector to corrode, no user pulling the wrong media.

IoT and appliance makers

You ship firmware, logs or configuration on a core that is part of the product, not a peripheral the customer swaps.

Assembly lines and integrators

You take the UDP or the semi-finished board and run your own housing, conformal coating or final test.

The specification — what we produce, and what you have to confirm

A module has no body, so there is nothing to look at and nothing to choose by photo. The product is this table. The right-hand column is the part most buyers skip, and it is where a module programme fails — not in production, but at the drawing stage.

Parameter What we produce What you must confirm before the run
Format Moulded UDP at 25 × 11.3 × 1.4 mm (long version) or the short version; semi-finished board at 12 × 48 × 4.5 mm The cavity or footprint you actually have. 25 mm and 22 mm take different parts — send the drawing, not the capacity.
Weight 0.819 g for the moulded module; 3.2 g for the semi-finished board Whether your line can place the part without a fixture, and how it is retained.
Capacity 4GB – 32GB on the moulded module; 128MB – 128GB on the semi-finished board The workload the storage serves, and the top of the range against current die supply.
Interface USB 2.0 on the moulded module; USB 2.0 or 3.0 on the board That your host enumerates the interface you are paying for, on the production board rather than a bench cable.
Silicon SanDisk, Toshiba, Micron, SK Hynix, Intel, Samsung — TSOP, BGA, LGA, COB, eMMC, A+ grade The grade and source in writing, plus your own incoming inspection method.
Controller Alcor, ITE, Xinbang, Micov — QFN, 24-pin, 48-pin, COB Host and firmware compatibility, tested on your board and locked for the programme.
Contact Standard USB-A 4-pin, gold plated Insertion cycles and retention method in your housing.
Marking Laser marking on the board version; no print area on the epoxy module Part number and lot format — this is what makes a field failure traceable later.
Packing Tray or antistatic bag for modules; boards 100 to a tray The tray or reel format your SMT line accepts. Loose modules in a bag arrive with bent contacts.
Testing Full-capacity write and read-back per unit, before packing The acceptance criteria you will judge the lot by — ours or yours, written before the run.

Writing the document itself? There is a UDP module specification template with the fields in the order a factory needs them.

Minimum order, and what the schedule is actually made of

Module buyers get told one number for MOQ and one number for lead time, and both are usually wrong because both depend on what you are asking for. Here is the honest version.

Item What it is Where it is fixed
Minimum order 50 pieces per design on a standard module or board. An ODM board outline carries its own tooling, and the first-run quantity is stated separately. On the quotation, per line — not assumed from the piece count.
Price basis Quoted per project against capacity and test scope. The published drive range (US$2–6) does not apply to a module. On the quotation, with the test scope written out.
Sample A physical module or board to test in your own device, before the bulk run. Sample stage — you approve, not us.
Artwork and approval 1–7 days, and on a module this means drawing sign-off and marking data rather than print colour. Your side. This is the stage that overruns.
Production 3–15 working days from approved sample and cleared payment. Stock capacities run at the short end; a new board outline adds design and tooling time before the clock starts. On the quotation, against your target date.
Testing 1–5 working days — full-capacity write and read-back is per unit, so it scales with the lot. On the quotation, as a separate step from production.
Transit and clearance 3–20 days depending on freight mode and destination. Neither side controls this entirely; plan the buffer rather than argue about it.

The four-stage split is the same one we use on custom microSD schedules — a single lead-time number hides which stage you can actually shorten. What drives each stage: production lead time.

From die to a module you can solder — six stages, and what is checkable

Every stage below has a decision attached to it that changes what arrives in the tray. If a supplier cannot say which stage a decision belongs to, the process description is decoration.

Stage What happens The decision made here What you can check
1. Die sorting and grading Incoming die is screened and graded before it is bonded or packaged. Grade decides retention and failure rate far more than it decides benchmark speed. Die grade and source Ask for the sourcing breakdown against your project.
2. Die attach and bonding Bare die is bonded to the substrate, or a packaged part is placed by machine. The format is chosen against capacity, cost target and the height your housing allows. Die package format Package format stated on the quotation; die marking visible on incoming inspection.
3. Controller pairing and programming The controller is paired with the flash and configured to the target capacity and host interface. A mismatch here enumerates on a bench and fails on a production board. Controller solution and package Test the sample on your own host, not on a laptop.
4. Moulding / encapsulation On a UDP the electronics are encapsulated in black epoxy at close to final size. On a semi-finished board this stage does not exist — the board stays bare for your housing. Module or bare board Cavity drawing and retention method match the part you receive.
5. Marking Laser marking or label on the board version. The epoxy module has no print area, so traceability has to live on the packing and the paperwork. Part number and lot format Lot code on the tray label matches the test record.
6. Test and pack Full-capacity write and read-back per unit, then tray or bag. An under-capacity part is caught here or it is caught by your customer. Acceptance criteria Test report shipped against the lot code — ask for it before you need it.

The same six stages are described for every format on the manufacturing process page, and the test methods are set out in how to test a memory card.

Where a UDP programme actually goes wrong

These are the six failures that recur on module orders. None of them is a production problem; five of the six are decided before production starts.

The trap Why it happens What to do instead
Footprint drawn from a datasheet The cavity is designed to a nominal length, then the actual moulding is 0.3 mm different and the part will not seat. Measure a physical sample before the PCB or housing is finalised. This is the cheapest hour in the whole programme.
Enumerates on the bench, not on the board Controller pairing was validated on a laptop USB port, while the production host has a hub, a longer trace or a different power budget. Require the sample to be tested on your actual host board, and lock the controller solution for the programme.
Capacity that holds on day one Die grade was never written down, so a mid-programme substitution is invisible until units fail in the field. Put the grade and source on the quotation and require written notice before any substitution.
Bent contacts in the tray Loose modules shipped in a bag because the tray looked like an unnecessary cost. Specify tray packing for anything above sample quantity. It costs almost nothing and it is the difference between a line that runs and a line that stops.
Nobody agrees who tests the finished unit We test the module; you assemble it into a housing. A module that passed here can still fail after assembly, and the argument is about who owns that. Write down where the functional test happens before the first order, not after the first failure.
No lot traceability There is no print area on the epoxy module, so nothing carries the batch identity into your factory. Tie the tray label to the lot code and the test record. That is what makes a claim settleable instead of arguable.

Manufacturer versus trading company — what actually differs

Factory-direct (WINTEL) Through a trading company
Where the specification is set On our own floor — capacity, controller, silicon grade and testing are configured against your order. By whichever factory takes the order that week.
What happens when material is short You are told before a substitution is made, because the silicon and controller are documented in the specification we quote. Substitution happens between you and the end factory, usually without notice.
Who owns the quality check Capacity and read/write verification run as part of our own production flow, before packing. Whatever the supplying factory did, which you cannot audit.
What you can ask to see The process, the test method and the registration record of the legal entity you are contracting with. A catalogue.

This comparison describes our own operation, not a claim about any named third party.

The legal entity you would be contracting with

  • Legal name (EN)Shenzhen Wintel Digital Technology Limited
  • Legal name (CN)深圳市微盛鑫数码科技有限公司
  • RegisteredChina, 2015-05-12
  • Team in this industry since2006
  • FactoryShenzhen, Guangdong, China
  • Factory floor5,000 m²
  • Export markets50+ countries

OEM or ODM on a module — what actually gets specified

On a finished drive the visible variable is the body. On a module there is no body: the whole product is the specification, which is why an OEM module order is a document rather than a colour choice. These are the four items that have to be written down before a module is quoted properly.

Item What OEM means here What ODM means here
Silicon grade Grade stated in writing, with the die marking your incoming inspection can check. Our standard grade for that capacity, stated on the quotation.
Controller solution Chosen against your host device and firmware, and locked for the programme. Our stock solution for that capacity band.
Test criterion Written to your acceptance criteria — full-capacity write, read-back, or your own plan. Our standard full-capacity test, with the report shipped against the lot code.
Marking and packing Your part number, your label data, your reel or tray format. Our marking, your brand if you want it on the pack.

If a supplier will not put the silicon grade and controller solution in writing, the "OEM" conversation has not started yet — see how to verify a flash supplier.

Price ladder for modules

Module pricing behaves differently from finished drives: there is no print set-up, so the fixed cost is the test and programming time rather than artwork. The published drive range (US$2–6) does not apply here — a module is priced against capacity and test scope, and the test scope is what buyers underestimate.

Quantity How it is priced What dominates the unit cost
50 – 499 Quoted per project Test and programming time per unit; there is nothing to amortise over.
500 – 4,999 Quoted against capacity and test scope Silicon grade, then test scope. A full-capacity read-back is not free and should be quoted as a step.
5,000 + Programme pricing with call-off releases NAND market. Lock the grade and the review cadence rather than a single number.

The two module formats we produce

One is soldered as fixed storage; the other is the bare board you build into your own housing. Both have a specification page with dimensions, weight, capacity range and the order notes.

Not sure which of the three formats fits — module, board or finished drive? Module vs board vs card, compared.

Send a specification, get a quote

Tell us the capacity, quantity, application and target date. We reply to business enquiries within 1 business day.

Or email cathy@go-wintel.com — answered by Cathy, sales engineer.

Frequently asked questions

Are you a UDP module manufacturer or a trading company?

A manufacturer. Shenzhen Wintel Digital Technology Limited produces UDP modules on its own floor in Shenzhen. We are not a reseller, a distributor or a marketplace seller.

What is a UDP module, exactly?

UDP means USB Disk in Package — NAND, controller and passive components moulded into one small package (25 × 11.3 × 1.4 mm, 0.819 g) that is soldered onto your PCB as fixed internal storage. It is the core of a USB drive, without the connector and housing.

What capacities do your UDP modules cover?

From 4GB to 32GB on the moulded module, and 128MB to 128GB on the semi-finished board. Tell us the device the storage must serve and we size the capacity and grade to that workload rather than defaulting to a single option.

How do you keep the module consistent across batches?

Capacity, silicon grade, controller solution and testing are stated on your quotation and held as quoted through production. A shortage becomes a conversation before any substitution, not a surprise on arrival.

Can you provide the semi-finished board instead of the UDP?

Yes. The semi-finished USB board (12 × 48 × 4.5 mm, 3.2 g) is the bare PCBA for buyers who run their own housing or final assembly. The UDP is the moulded core for buyers who solder directly.

Which silicon and controllers do you use?

SanDisk, Toshiba, Micron, SK Hynix, Intel, Samsung, in TSOP, BGA, LGA, COB and eMMC formats, at A+ grade, with controllers from Alcor, ITE, Xinbang, Micov. We are not an authorised agent for any NAND brand — we buy and sort flash and state the grade and source against your project.

Do you have certifications?

We list only certifications we hold and can show documentation for. Where a certificate is not yet published on our site, we do not claim it.

WhatsApp / WeChat Request a quote